Out of Stock

XPSMC16ZC

Telemecanique - safety controller XPS-MC - 24 V DC - 16 input - 32 LEDs signalling

Current response time:

14 Minutes 54 Seconds

*Santa Clara Systems is not a Telemecanique Authorized Distributor.

Description: safety controller XPS-MC - 24 V DC - 16 input - 32 LEDs signalling
Product weight: 1.81 lb(US) (0.82 kg)
Range of product: Preventa Safety automation
IP degree of protection: IP20 conforming to EN/IEC 60529
Standards: EN 1760-1/ISO 13856-1EN 574/ISO 13851EN 954-1/EN/ISO 13849-1EN/IEC 60204-1EN/IEC 60947-5-1EN/IEC 61496-1IEC 61508
Width: 2.91 in (74 mm)
Height: 5.96 in (151.5 mm)
Depth: 6.02 in (153 mm)
[Ui] rated insulation voltage: 300 V, degree of pollution 2 conforming to IEC 60647-5-1, DIN VDE 0110 part 1
[Uimp] rated impulse withstand voltage: 4 kV overvoltage category III conforming to IEC 60647-5-1, DIN VDE 0110 part 1
Mounting support: Mounting plate
[Ith] conventional free air thermal current: <= 16 A for relay output<= 6.5 A for static output circuit
[Uc] control circuit voltage: 28.8 V
[Us] rated supply voltage: 24 V DC - 20...20 %
Associated fuse rating: 16 A gL for power supply4 A gL for relay output6 A fast blow for relay output
Response time: Configurable : 20 ms or 30 ms with software XPSMCWIN
Breaking capacity: 1.5 A/24 V - L/R = 50 ms, DC-13 relay output2 A/24 V for static output circuit
Output type: 2 relays, 2 NO contacts (4 NO total) circuit(s)Solid state, 6 circuit(s), volt-free
Function of module: Dynamic monitoring of hydraulic valves on linear pressesEccentric pressEmergency stop monitoring, with or without time delay, 1 or 2-channel wiringEnabling switch monitoring, 2 or 3 contactsFoot switch monitoringGuard monitoring for injection presses and blowing machinesGuard monitoring with 1 or 2 limit switchesHydraulic pressMagnetic switch monitoringMonitoring safety stop at top dead centre on eccentric pressMuting function of light curtainsPosition selectorSafety mat monitoringSafety time delaysShaft/chain breaking monitorZero speed detectionLight curtain monitoring (category 4) conforming to EN/IEC 61496Two-hand control (category 3) conforming to EN 574/ISO 13851
Product or component type: Configurable safety controller
Synchronisation time between inputs: Depending on configuration selected
Ambient air temperature for operation: 14...131 °F (-10...55 °C)

Safety module name: XPSMC
power consumption in W: 12 W
Ambient air temperature for storage: -13...185 °F (-25...85 °C)
Safety use category: Category 4 maximum conforming to EN 954-1/EN/ISO 13849-1PLE maximum conforming to EN/ISO 13849-1SIL 3 maximum conforming to IEC 61508
Input protection type: External fuse 16 A
Type of start: Configurable
Line resistance: 100 Ohm 2000 m
Product certifications: CSATÜVUL
Number of inputs: 16
Communication port protocol: CANopen with 1 SUB-D 9-pin male port(s), serial link, transmission rate: 20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 800 kbps or 1 MbpsModbus with 1 RJ45 port(s), serial link, transmission rate: 1200 bps, 2400 bps, 4800 bps, 9600 bps or 19200 bps
Output thermal current: 4 A for both outputs simultaneously6 A for 1 output and 2 A for the other relay output
Safety level: Can reach PL e/category 4 conforming to EN 954-1/EN/ISO 13849-1Can reach SIL 3 conforming to IEC 61508
Minimum output current: 10 mA relay output
Minimum output voltage: 17 V relay output
Method of access: Slave
Exchange size: 14 words
Number of addresses: 1...247 Modbus1...127 CANopen
Parity: Even ModbusNo ModbusOdd Modbus
Data format: 1 start bit/8 data bits1 stop bit even or odd2 stop bits without parityRTU (Remote Terminal Unit) mode
Supported modbus function: 01: 8-bit output data/32-bit input data02: 32-bit input data/8-bit output data03: information and errors
Local signalling: 32 LEDs

Santa Clara Systems specializes in hard-to-find parts. Choose from our overstock inventory and save on XPSMC16ZC . Santa Clara Systems carries 10,431 items from Telemecanique.