Out of Stock

ATV61HC16N4

Telemecanique - SPEEDDRIVE,250HP,460V,ATV61

Current response time:

By 5AM PT on Monday

Emergency?

*Santa Clara Systems is not a Telemecanique Authorized Distributor.

Description: SPEEDDRIVE,250HP,460V,ATV61
Product weight: 132.28 lb(US) (60 kg)
Range of product: Altivar 61
IP degree of protection: IP00 conforming to EN/IEC 60529, IP00 conforming to EN/IEC 61800-5-1, IP30 on side parts conforming to EN/IEC 60529, IP30 on side parts conforming to EN/IEC 61800-5-1, IP30 on the front panel conforming to EN/IEC 60529, IP30 on the front panel conforming to EN/IEC 61800-5-1, IP41 on upper part conforming to EN/IEC 60529, IP41 on upper part conforming to EN/IEC 61800-5-1, IP54 on lower part conforming to EN/IEC 60529, IP54 on lower part conforming to EN/IEC 61800-5-1
Standards: UL Type 1, EN 55011 class A group 2, EN 61800-3 environments 1 category C3, EN/IEC 61800-3, EN 61800-3 environments 2 category C3, IEC 60721-3-3 class 3C2, EN/IEC 61800-5-1
Width: 12.6 in (320 mm)
Height: 36.22 in (920 mm)
Depth: 14.84 in (377 mm)
Operating altitude: <= 3280.84 ft. (1000 m) without derating, 3280.84...9842.52 ft. (1000...3000 m) with current derating 1 % per 100 m
Tightening torque: L1/R, L2/S, L3/T, U/T1, V/T2, W/T3 212.39 lbf.in (24 N.m) / 212 lb.in, PA, PB 106.19 lbf.in (12 N.m) / 106 lb.in, PC/-, PO, PA/+ 362.83 lbf.in (41 N.m) / 360 lb.in, AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR 5.31 lbf.in (0.6 N.m)
Vibration resistance: 1.5 mm peak to peak (f = 3...10 Hz) conforming to EN/IEC 60068-2-6, 0.6 gn (f = 10...200 Hz) conforming to EN/IEC 60068-2-6
Shock resistance: 7 gn 11 ms conforming to EN/IEC 60068-2-27
Electrical connection: AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR terminal 2.5 mm / AWG 14, L1/R, L2/S, L3/T, U/T1, V/T2, W/T3 terminal 2 x 100 mm / 2 x 250 kcmil, PA, PB terminal 60 mm / 250 kcmil, PC/-, PO, PA/+ terminal 2 x 100 mm / 2 x 250 kcmil
Insulation resistance: > 1 mOhm at 500 V DC for 1 minute to earth
motor power kW: 110 kW 3 phasesat 380...480 V
[Us] rated supply voltage: 380...480 V (- 15...10 %)
Relative humidity: 5...95 % without condensation conforming to IEC 60068-2-3, 5...95 % without dripping water conforming to IEC 60068-2-3
Protection type: Drive against exceeding limit speed, Drive against input phase loss, Drive break on the control circuit, Drive input phase breaks, Drive line supply overvoltage, Drive line supply undervoltage, Drive overcurrent between output phases and earth, Drive overheating protection, Drive overvoltages on the DC bus, Drive power removal, Drive short-circuit between motor phases, Drive thermal protection, Motor motor phase break, Motor power removal, Motor thermal protection
Response time: <= 100 ms in STO (Safe Torque Off), R1A, R1B, R1C <= 7 ms, tolerance +/- 0.5 ms, R2A, R2B <= 7 ms, tolerance +/- 0.5 ms
Switching frequency: 2...8 kHz adjustable, 2.5...8 kHz with derating factor
Product destination: Synchronous motors, Asynchronous motors
Noise level: 60.5 dB conforming to 86/188/EEC
Product or component type: Variable speed drive
Supply voltage limits: 323...528 V
Dielectric strength: 3535 V DC between earth and power terminals, 5092 V DC between control and power terminals
Product specific application: Pumping and ventilation machine
Supply frequency: 50...60 Hz (- 5...5 %)
Electromagnetic compatibility: Conforming to IEC 61000-4-2 level 3, Conforming to IEC 61000-4-11, Conforming to IEC 61000-4-6 level 3, Conforming to IEC 61000-4-3 level 3, Conforming to IEC 61000-4-4 level 4
Component name: ATV61
Network frequency: 47.5...63 Hz
Continuous output current: 215 A at 2.5 kHz, 380 V 3 phases, 215 A at 2.5 kHz, 460 V 3 phases
Product certifications: C-Tick, UL, CSA, DNV, NOM 117, GOST
Motor power hp: 150 hp 3 phasesat 380...480 V
Output frequency: 0.1...500 Hz
Pollution degree: 3 conforming to EN/IEC 61800-5-1, 3 conforming to UL 840
Speed range: 1...100 in open-loop mode, without speed feedback
Phase: 3 phases
Speed accuracy: +/- 10 % of nominal slip 0.2 Tn to Tn torque variation without speed feedback
Line current: 168 Afor 480 V 3 phases 110 kW / 150 hp, 202 Afor 380 V 3 phases 110 kW / 150 hp
Torque accuracy: +/- 15 % in open-loop mode, without speed feedback
EMC filter: Level 3 EMC filter
Transient overtorque: 130 % of nominal motor torque, +/- 10 %for 60 s
Variant: Without DC choke
Braking torque: 30 % without braking resistor, <= 125 % with braking resistor
Ambient air temperature for operation: 14...113 F (-10...45 C) without derating, 113...140 F (45...60 C) with derating factor

Assembly style: With heat sink
Regulation loop: Frequency PI regulator
Ambient air temperature for storage: -13...158 F (-25...70 C)
Apparent power: 133 kVAfor 380 V 3 phases 110 kW / 150 hp
Motor slip compensation: Automatic whatever the load, Not available in voltage/frequency ratio (2 or 5 points), Can be suppressed, Adjustable
prospective line Isc: 35 kA 3 phases
Local signaling: 1 LED red presence of drive voltage
Maximum transient current: 258 A for 60 s 3 phases
Output voltage: <= power supply voltage
Nominal switching frequency: 2.5 kHz
Isolation: Between power and control terminals
Type of cable: With an IP21 or an IP31 kit: 3-strand IEC cableat 104 F (40 C), copper 70 C PVC, Without mounting kit: 1-strand IEC cableat 113 F (45 C), copper 70 C PVC, Without mounting kit: 1-strand IEC cableat 113 F (45 C), copper 90 C XLPE/EPR, With UL Type 1 kit: 3-strand UL 508 cableat 104 F (40 C), copper 75 C PVC
Asynchronous motor control profile: Voltage/frequency ratio - Energy Saving, quadratic U/f, Voltage/frequency ratio, 2 points, Voltage/frequency ratio, 5 points, Flux vector control without sensor, standard
Synchronous motor control profile: Vector control without sensor, standard
Communication port protocol: Modbus, CANopen
Supply: Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 %, <= 10 mA for overload and short-circuit protection, Internal supply 24 V DC (21...27 V), <= 200 mA for overload and short-circuit protection, External supply 24 V DC (19...30 V)
Type of polarization: No impedance Modbus
Analogue input number: 2
Option card: APOGEE FLN communication card, BACnet communication card, CC-Link communication card, Controller inside programmable card, DeviceNet communication card, Ethernet/IP communication card, Fipio communication card, I/O extension card, Interbus-S communication card, LonWorks communication card, METASYS N2 communication card, Modbus Plus communication card, Modbus TCP communication card, Modbus/Uni-Telway communication card, Multi-pump card, Profibus DP communication card, Profibus DP V1 communication card
Analogue input type: AI1-/Al1+ bipolar differential voltage +/- 10 V DC, input voltage 24 V max, resolution 11 bits + sign, AI2 software-configurable current 0...20 mA, impedance 242 Ohm, resolution 11 bits, AI2 software-configurable voltage 0...10 V DC, input voltage 24 V max, impedance 30000 Ohm, resolution 11 bits
Sampling duration: Discrete input LI6 (if configured as logic input) 2 ms, +/- 0.5 ms, Analog input AI1-/Al1+ 2 ms, +/- 0.5 ms, Analog input Al2 2 ms, +/- 0.5 ms, Analog output AO1 2 ms, +/- 0.5 ms, Discrete input LI1...LI5 2 ms, +/- 0.5 ms
Accuracy: AI1-/Al1+ +/- 0.6 % for a temperature variation 60 C, AI2 +/- 0.6 % for a temperature variation 60 C, AO1 +/- 1 % for a temperature variation 60 C
Linearity error: AI1-/Al1+ +/- 0.15 % of maximum value, AI2 +/- 0.15 % of maximum value, AO1 +/- 0.2 %
Analogue output number: 1
Analogue output type: AO1 software-configurable current, analogue output range 0...20 mA, impedance 500 Ohm, resolution 10 bits, AO1 software-configurable logic output 10 V, <= 20 mA, AO1 software-configurable voltage, analogue output range 0...10 V DC, impedance 470 Ohm, resolution 10 bits
Discrete output number: 2
Discrete output type: (R1A, R1B, R1C) configurable relay logic NO/NC, electrical durability 100000 cycles, (R2A, R2B) configurable relay logic NO, electrical durability 100000 cycles
Minimum switching current: Configurable relay logic 3 mAat 24 V DC
Maximum switching current: R1, R2 on resistive load, 5 A at 30 V DC, cos phi = 1, 0 ms, R1, R2 on inductive load, 2 A at 30 V DC, cos phi = 0.4, 7 ms, R1, R2 on resistive load, 5 A at 250 V AC, cos phi = 1, 0 ms, R1, R2 on inductive load, 2 A at 250 V AC, cos phi = 0.4, 7 ms
Discrete input number: 7
Discrete input type: (LI1...LI5) programmable, 24 V DC, voltage limits <= 30 V, with level 1 PLC, impedance 3500 Ohm, (LI6) switch-configurable, 24 V DC, voltage limits <= 30 V, with level 1 PLC, impedance 3500 Ohm, (LI6) switch-configurable PTC probe, 0...6, impedance 1500 Ohm, (PWR) safety input, 24 V DC, voltage limits <= 30 V, impedance 1500 Ohm
Discrete input logic: LI1...LI5 positive logic (source), < 5 V (state 0), > 11 V (state 1), LI1...LI5 negative logic (sink), > 16 V (state 0), < 10 V (state 1), LI6 (if configured as logic input) negative logic (sink), > 16 V (state 0), < 10 V (state 1), LI6 (if configured as logic input) positive logic (source), < 5 V (state 0), > 11 V (state 1)
Acceleration and deceleration ramps: S, U or customized, Linear adjustable separately from 0.01 to 9000 s, Automatic adaptation of ramp if braking capacity exceeded, by using resistor
Braking to standstill: By DC injection
Frequency resolution: Analog input 0.024/50 Hz, Display unit 0.1 Hz
Connector type: 1 RJ45 Modbus on front face, 1 RJ45 Modbus on terminal, Male SUB-D 9 on RJ45 CANopen
Physical interface: 2-wire RS 485 Modbus
Transmission frame: RTU Modbus
Transmission rate: 20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps CANopen, 4800 bps, 9600 bps, 19200 bps, 38.4 Kbps Modbus on terminal, 9600 bps, 19200 bps Modbus on front face
Data format: 8 bits, 1 stop, even parity Modbus on front face, 8 bits, odd even or no configurable parity Modbus on terminal
Number of addresses: 1...247 Modbus, 1...127 CANopen
Method of access: Slave CANopen
Marking: CE
Operating position: Vertical +/- 10 degree

Santa Clara Systems specializes in hard-to-find parts. Choose from our overstock inventory and save on ATV61HC16N4 . Santa Clara Systems carries 10,327 items from Telemecanique.