ATV320U15N4C

Telemecanique - variable speed drive ATV320 - 1.5kW - 380...500V - 3 phase - compact

Current response time:

By 5AM PT on Friday

Emergency?

*Santa Clara Systems is not a Telemecanique Authorized Distributor.

Description: variable speed drive ATV320 - 1.5kW - 380...500V - 3 phase - compact
Product weight: 2.87 lb(US) (1.3 kg)
Range of product: Altivar Machine ATV320
IP degree of protection: IP20 conforming to EN/IEC 61800-5-1
Standards: EN/IEC 61800-3, EN/IEC 61800-3 environment 1 category C2, EN/IEC 61800-5-1, IEC 60721-3, IEC 61508, IEC 13849-1
Device short name: ATV320
Width: 4.13 in (105 mm)
Height: 142 mm, 188 mm with EMC plate
Depth: 6.22 in (158 mm)
Operating altitude: <= 3280.84 ft. (1000 m) without derating, 3280.84...9842.52 ft. (1000...3000 m) with current derating 1 % per 100 m
Vibration resistance: 1.5 mm peak to peak (f = 2...13 Hz) conforming to EN/IEC 60068-2-6, 1 gn (f = 13...200 Hz) conforming to EN/IEC 60068-2-6
Shock resistance: 15 gn during 11 ms conforming to EN/IEC 60068-2-27
Electrical connection: Control, screw terminal: 0.5...1.5 mm AWG 20...AWG 16, Motor/braking resistor, screw terminal: 2.5...6 mm AWG 14...AWG 10, Power supply, screw terminal: 2.5...6 mm AWG 14...AWG 10
Insulation resistance: > 1 mOhm at 500 V DC for 1 minute to earth
motor power kW: 1.5 kW heavy duty
[Us] rated supply voltage: 380...500 V (- 15...10 %)
Relative humidity: 5...95 % without condensation conforming to IEC 60068-2-3, 5...95 % without dripping water conforming to IEC 60068-2-3
Protection type: Drive: thermal protection, Drive: overcurrent between output phases and earth, Drive: input phase breaks, Drive: overheating protection, Drive: short-circuit between motor phases
Switching frequency: 4...16 kHz with current derating, 2...16 kHz adjustable
Degree of protection: UL type 1 with UL type 1 conformity kit
Output voltage: <= power supply voltage
Isolation: Between power and control terminals
Product or component type: Variable speed drive
Permissible temporary current boost: 1.5 x In during 60 s heavy duty
Product specific application: Complex machines
Speed range: 1...100 with asynchronous motor in open-loop mode
Noise level: 51 dB conforming to 86/188/EEC
Speed accuracy: +/- 10 % of nominal slip 0.2 Tn to Tn
power dissipation in W: 61 W (fan) at 380 V, 4 kHz
Format of the drive: Compact
Torque accuracy: +/- 15 %
Volume of cooling air: 4755.18 Gal/hr(US) (18 m3/h)
Product destination: Asynchronous motors, Synchronous motors
Transient overtorque: 170...200 % of nominal motor torque
Operating position: Vertical +/- 10 degree
EMC filter: Class C2 EMC filter integrated
Braking torque: <= 170 % with braking resistor during 60 s
Electromagnetic compatibility: Conducted radio-frequency immunity test conforming to IEC 61000-4-6 level 3, Electrical fast transient/burst immunity test conforming to IEC 61000-4-4 level 4, Electrostatic discharge immunity test conforming to IEC 61000-4-2 level 3, Radiated radio-frequency electromagnetic field immunity test conforming to IEC 61000-4-3 level 3, Voltage dips and interruptions immunity test conforming to IEC 61000-4-11, 1.2/50 s - 8/20 s surge immunity test conforming to IEC 61000-4-5 level 3
Regulation loop: Adjustable PID regulator
Pollution degree: 2 conforming to EN/IEC 61800-5-1
Motor slip compensation: Adjustable 0...300 %, Not available in voltage/frequency ratio (2 or 5 points), Automatic whatever the load
Type of cooling: Fan
Acceleration and deceleration ramps: U, Deceleration ramp automatic stop DC injection, Deceleration ramp adaptation, Ramp switching, Linear, CUS, S
Phase: 3 phases
Braking to standstill: By DC injection
Ambient air temperature for operation: 14...122 F (-10...50 C) without derating, 122...140 F (50...60 C) with derating factor
Supply frequency: 50...60 Hz (- 5...5 %)

Frequency resolution: Display unit: 0.1 Hz, Analog input: 0.012/50 Hz
Ambient air temperature for storage: -13...158 F (-25...70 C)
Motor power hp: 2 hp heavy duty
Connector type: 1 RJ45 Modbus/CANopen on control terminal
Line current: 6.4 A at 380 V heavy duty, 4.9 A at 500 V heavy duty
Physical interface: 2-wire RS 485 Modbus
Product certifications: RCM, UL, EAC, CSA, NOM 117
prospective line Isc: <= 5 kA
Transmission frame: RTU Modbus
Marking: CE
Apparent power: 4.2 kVA at 500 V heavy duty
Transmission rate: 4.8, 9.6, 19.2, 38.4 kbit/s Modbus, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps CANopen
Continuous output current: 4.1 A at 4 kHz heavy duty
Data format: 8 bits, configurable odd, even or no parity Modbus
Maximum transient current: 6.2 A during 60 s heavy duty
Type of polarization: No impedance Modbus
Asynchronous motor control profile: Voltage/frequency ratio - Energy Saving, quadratic U/f, Flux vector control without sensor, standard, Voltage/frequency ratio, 2 points, Flux vector control without sensor - Energy Saving, Voltage/frequency ratio, 5 points
Number of addresses: 1...247 Modbus, 1...127 CANopen
Synchronous motor control profile: Vector control without sensor
Method of access: Slave CANopen
Speed drive output frequency: 0.1...599 Hz
Supply: Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC (+/- 5 %) current <= 10 mA (overload and short-circuit protection)
Nominal switching frequency: 4 kHz
Local signaling: 1 LED green CANopen run, 1 LED red CANopen error, 1 LED red drive fault
Safety function: STO (safe torque off) SIL 3, SS1 (safe stop 1), SMS (safe maximum speed), SLS (safe limited speed), GDL (guard door locking)
Communication port protocol: CANopen, Modbus
Option card: Communication module: CANopen daisy chain RJ45, Communication module: CANopen SUB-D 9, Communication module: CANopen open style terminal block, Communication module: EtherCAT RJ45, Communication module: DeviceNet, Communication module: Ethernet/IP, Communication module: Profibus DP V1, Communication module: Profinet, Communication module: Ethernet Powerlink
Analogue input number: 3
Analogue input type: Voltage (AI1): 0...10 V DC, impedance 30000 Ohm, resolution 10 bits, Bipolar differential voltage (AI2): +/- 10 V DC, impedance 30000 Ohm, resolution 10 bits, Current (AI3): 0...20 mA (or 4-20 mA, x-20 mA, 20-x mA or other patterns by configuration), impedance 250 Ohm, resolution 10 bits
Discrete input number: 7
Discrete input type: Programmable (sink/source) (DI1...DI4): 24...30 V DC: level 1 PLC, Programmable as pulse input 20 kpps (DI5): 24...30 V DC: level 1 PLC, Switch-configurable PTC probe (DI6): 24...30 V DC, Safe torque off (STO): 24...30 V DC, impedance 1500 Ohm
Discrete input logic: Negative logic (sink): : DI1...DI6, > 19 V (state 0) < 13 V (state 1), Positive logic (source): : DI1...DI6, < 5 V (state 0) > 11 V (state 1)
Analogue output number: 1
Analogue output type: Software-configurable current (AQ1): 0...20 mA, impedance 800 Ohm, resolution 10 bits, Software-configurable voltage (AQ1): 0...10 V, impedance 470 Ohm, resolution 10 bits
Sampling duration: Analog input (AI1, AI2, AI3): 2 ms, Analog output (AQ1): 2 ms
Accuracy: Analog input AI1, AI2, AI3: +/- 0.2 % for a temperature of -10...60 C, Analog input AI1, AI2, AI3: +/- 0.5 % for a temperature of 25 C, Analog output AQ1: +/- 1 % for a temperature of 25 C, Analog output AQ1: +/- 2 % for a temperature of -10...60 C
Linearity error: Analog input (AI1, AI2, AI3): +/- 0.2...0.5 % of maximum value, Analog output (AQ1): +/- 0.3 %
Discrete output number: 3
Discrete output type: Configurable relay logic NO/NC (R1A, R1B, R1C): electrical durability 100000 cycles, Configurable relay logic NO (R2A, R2B): electrical durability 100000 cycles, Logic (LO)
Refresh time: Logic input (DI1...DI6): 8 ms (+/- 0.7 ms), Relay output (R1A, R1B, R1C): 2 ms, Relay output (R2A, R2C): 2 ms
Minimum switching current: Relay output (R1, R2): 5 mA at 24 V DC
Maximum switching current: Relay output (R1) on resistive load (cos phi = 1: 3 A at 250 V AC, Relay output (R1) on resistive load (cos phi = 1: 4 A at 30 V DC, Relay output (R1, R2) on inductive load (cos phi = 0.4: 2 A at 250 V AC, Relay output (R1, R2) on inductive load (cos phi = 0.4: 2 A at 30 V DC, Relay output (R2) on resistive load (cos phi = 1: 5 A at 250 V AC, Relay output (R2) on resistive load (cos phi = 1: 5 A at 30 V DC
Specific application: Machinery
Discrete and process manufacturing: Hoisting self erecting, Material handling carousel, Material handling conveyor, Material handling lifting platfrom, Material handling palletizers - medium performance, Material handling transfer table, Material handling turn table, Material working (wood, ceramic, stone, pvc, metal) cutting - medium accuracy, Material working (wood, ceramic, stone, pvc, metal) drilling, Material working (wood, ceramic, stone, pvc, metal) saw, Packaging bagging, Packaging feed conveyor low performance, Packaging filling bottles - intermittent operation, Packaging linear labeling, Packaging other application, Packaging stretching wrapping, Packaging tray take, Textile knitting, Textile printing machines, Textile spinning, Washing machines car, Washing machines other application, Hoisting standard crane - travelling or trolley
Power range: 1.1...2 kW 380...440 V 3 phases, 1.1...2 kW 480...500 V 3 phases
Motor starter type: Variable speed drive

Santa Clara Systems specializes in hard-to-find parts. Choose from our overstock inventory and save on ATV320U15N4C . Santa Clara Systems carries 10,327 items from Telemecanique.