ATV630D55N4

Telemecanique - Variable Speed Drive

Current response time:

By 5AM PT on Monday

Emergency?

*Santa Clara Systems is not a Telemecanique Authorized Distributor.

Description: Variable Speed Drive
Range of product: Altivar Process ATV600
IP degree of protection: IP21 conforming to IEC 61800-5-1
Standards: UL 508C
Device short name: ATV630
Width: 290 mm
Height: 922 mm
Depth: 323 mm
Operating altitude: <= 1000 m without
Vibration resistance: 1.5 mm peak to peak (f= 213 Hz) conforming to IEC 60068-2-6
Shock resistance: 15 gn for 11 ms conforming to IEC 60068-2-27
Electrical connection: Control: removable screw terminals0.5...1.5 mm/AWG 20...AWG 16
Insulation resistance: > 1 MOhm 500 V DC for 1 minute to earth
motor power kW: 55 kW (normal duty)
[Us] rated supply voltage: 380...480 V - 15...10 %
Relative humidity: 595 % without condensation conforming to IEC 60068-2-3
Protection type: Thermal protection: motor
Switching frequency: 2.5...8 kHz with derating factor
Degree of protection: UL type 1 conforming to UL 508C
Product or component type: Variable speed drive
Product specific application: Process and utilities
Variant: Standard version
Mounting mode: Wall mount
EMC filter: Integrated with 150 m conforming to EN/IEC 61800-3 category C3
Type of cooling: Forced convection
Supply frequency: 50...60 Hz - 5...5 %
Network number of phases: 3 phases
Motor power hp: 75 hp normal duty
Line current: 97.2 A at 380 V (normal duty)
prospective line Isc: 50 kA
Apparent power: 70 kVA at 480 V (normal duty)
Continuous output current: 106 A at 2.5 kHz for normal duty
Maximum transient current: 116.6 A during 60 s (normal duty)
Asynchronous motor control profile: Constant torque standard
Synchronous motor control profile: Permanent magnet motor
Output frequency: 0.00010.5 kHz
Speed drive output frequency: 0.1599 Hz
Nominal switching frequency: 2.5 kHz
Safety function: STO (safe torque off) SIL 3
Discrete input logic: 16 preset speeds
Communication port protocol: Ethernet
Option card: Slot A: communication module, Profibus DP V1
Output voltage: <= power supply voltage
Permissible temporary current boost: 1.1 x In during 60 s (normal duty)
Motor slip compensation: Not available in permanent magnet motor law
Acceleration and deceleration ramps: Linear adjustable separately from 0.01...9999 s
Braking to standstill: By DC injection
Frequency resolution: Display unit: 0.1 Hz

Connector type: RJ45 (on the remote graphic terminal) for Ethernet/Modbus TCP
Physical interface: 2-wire RS 485 for Modbus serial
Transmission frame: RTU for Modbus serial
Transmission rate: 10/100 Mbit/s for Ethernet IP/Modbus TCP
Exchange mode: Half duplex, full duplex, autonegotiation Ethernet/Modbus TCP
Data format: 8 bits, configurable odd, even or no parity for Modbus serial
Type of polarization: No impedance for Modbus serial
Number of addresses: 1247 for Modbus serial
Method of access: Slave Modbus TCP
Supply: External supply for digital inputs: 24 V DC (1930 V), <1.25 mA, protection type: overload and short-circuit protection
Local signalling: 3 LEDslocal diagnostic:
Net weight: 56.5 kg
Analogue input number: 3
Analogue input type: AI1, AI2, AI3 software-configurable voltage: 0...10 V DC, impedance: 30 kOhm, resolution 12 bits
Discrete input number: 8
Discrete input type: DI1...DI6 programmable, 24 V DC (<= 30 V), impedance: 3.5 kOhm
Input compatibility: DI1...DI6: discrete input level 1 PLC conforming to EN/IEC 61131-2
Analogue output number: 2
Analogue output type: Software-configurable voltage AO1, AO2: 0...10 V DC impedance 470 Ohm, resolution 10 bits
Sampling duration: 2 ms +/- 0.5 ms (DI1...DI4) - discrete input
Linearity error: AI1, AI2, AI3: +/- 0.15 % of maximum value for analog input
Relay output number: 3
Relay output type: Configurable relay logic R1: fault relay NO/NC electrical durability 100000 cycles
Refresh time: Relay output (R1, R2, R3): 5 ms (+/- 0.5 ms)
Minimum switching current: Relay output R1, R2, R3: 5 mA at 24 V DC
Maximum switching current: Relay output R1, R2, R3 on resistive load, cos phi = 1: 3 A at 250 V AC
Isolation: Between power and control terminals
Variable speed drive application selection: Building - HVAC Compressor centrifugal
Motor power range AC-3: 55100 kW at 380440 V 3 phases
Noise level: 62.4 dB conforming to 86/188/EEC
power dissipation in W: Natural convection: 131 W at 380 V, switching frequency 2.5 kHz
Volume of cooling air: 295 m3/h
Operating position: Vertical +/- 10 degree
maximum THDI: <48 % from 80...100 % of load conforming to IEC 61000-3-12
Electromagnetic compatibility: Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2
Pollution degree: 2 conforming to EN/IEC 61800-5-1
Ambient air temperature for operation: -1550 C (without)
Ambient air temperature for storage: -4070 C
Environmental characteristic: Chemical pollution resistance class 3C3 conforming to EN/IEC 60721-3-3
Product certifications: CSA
Marking: CE
Sustainable offer status: Green Premium product
REACh Regulation: REACh Declaration
Mercury free: Yes
China RoHS Regulation: China RoHS declaration
Environmental Disclosure: Product Environmental Profile
Circularity Profile: End of Life Information
WEEE: The product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins

Santa Clara Systems specializes in hard-to-find parts. Choose from our overstock inventory and save on ATV630D55N4 . Santa Clara Systems carries 10,327 items from Telemecanique.

We are in the process of adding data and downloadable material for this item. Please search similar items for more information related to this product.